復合環氧樹脂橋架在實際橋架使用中也可以稱為是復合型玻璃鋼橋架，其成型過程即玻璃鋼制品的品質形成過程。由于復合環氧樹脂橋架可以被看作是一種由多種材料組成的復合結構，因此生產對于復合環氧樹脂橋架來說非常重要，而這種結構在制作過程中受到各種因素的制約。所以，制作方法雖然簡單，但需要注意一些生產環境的細節，使得復合環氧樹脂橋架在應用時更加，也對工藝和操作技能的要求更加。生產復合環氧樹脂橋架時應注意以下四點生產環境要求。

Composite epoxy resin bridge can also be referred to as composite fiberglass bridge in actual use, and its forming process is the quality formation process of fiberglass products. Due to the fact that composite epoxy resin cable trays can be regarded as a composite structure composed of multiple materials, production is crucial for composite epoxy resin cable trays, which are constrained by various factors during the manufacturing process. So, although the production method is simple, it is necessary to pay attention to some details of the production environment to make the composite epoxy resin bridge safer in application, and also require more professional process and operation skills. When producing composite epoxy resin cable trays, the following four environmental requirements should be noted.

一、生產復合環氧樹脂橋架位置

1、 Production of composite epoxy resin bridge positions

車間位置不宜建在水邊，水邊的環境太過潮濕，會影響生產橋架的濕度。生產復合環氧樹脂橋架四周要注意防火，不得堆放可燃物，應留有消防車輛通道，并設消火栓。

The workshop should not be located near the water, as the environment near the water is too humid and can affect the humidity of the production bridge. Attention should be paid to fire safety around the production of composite epoxy resin bridge frames. Combustible materials should not be stacked, and there should be a passage for firefighting vehicles and fire hydrants installed.

二、防爆

2、 Explosion proof safety

車間電器燈具較好是防爆的，嚴禁在車間內臨時亂接電線，過多的線路影響復合環氧樹脂橋架生產的用電。

The electrical lighting fixtures in the workshop are explosion-proof and it is strictly prohibited to connect wires randomly in the workshop. Excessive wires will affect the electrical safety of composite epoxy resin bridge production.

三、消防設施

3、 Firefighting facilities

生產車間注意消防設施的合理安排，在廠房入口處設置滅火器、沙箱、消防毯，廠房附近設置水龍頭。工場里的煙火。

Pay attention to the reasonable arrangement of fire protection facilities in the production workshop, set up fire extinguishers, sandboxes, and fire blankets at the entrance of the factory building, and set up faucets near the factory building. Fireworks in the factory.

四、生產溫濕度

4、 Production temperature and humidity

可以為生產溫度創造條件，使車間能達到調溫調濕的目的，冬季大于15度，夏季小于30度，較好控制溫度在20-25度之間，濕度應保持在75%以下，車間應放置干濕溫度計，若是沒有辦法控制溫度則可以經常開門窗通風，保持室內空氣流通。

It can create conditions for production temperature, so that the workshop can achieve the purpose of temperature and humidity control. When the temperature is above 15 degrees in winter and less than 30 degrees in summer, it is better to control the temperature between 20-25 degrees, and the humidity should be kept below 75%. The workshop should place a dry and wet thermometer. If the temperature cannot be controlled, doors and windows can be opened frequently for ventilation to maintain indoor air circulation.

本文由濟南電纜橋架友情奉獻.更多有關的知識請點擊:http://m.zkhtkj.cn真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Jinan Cable Tray Friendship. For more information, please click: http://m.zkhtkj.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned